686 PLUS

ULTRA HIGH GLOSS 686 PLUS is a Self-Crosslinking Acrylic /Polyurethane low V.O.C. Sealer that has great chemical resistance, early water-resistance, and good hot tire resistance. 686 PLUS has a v.o.c. below 100. Meets all Socal A.Q.M.D. requirements. It performs like, and looks better than oil based lacquer. It is water based, and a breathable sealer. Use 686 PLUS in areas where hydrostatic pressure exists. 686 PLUS meets, or beats the performance any product in gloss, depth of shine, protection and hardness. And it is easy to work with, and no overwhelming, or depressing heavy odors.

ULTRA HIGH GLOSS 686 PLUS is both a sealer and decorative finish for use on porous surfaces like stone, masonry, paver tiles, brick, clay and concrete. It provides a hard shell water resistant shiny finish that gives the appearance of a wet ceramic glaze. The results are revolutionary compared with other oil, or water based products.

If you have not used 686 PLUS before; try some on a test sample to see that it is the effect and that it offers the protection you desire. If more traction is needed; an anti-skid agent can be added to the final coat.

When applying ULTRA HIGH GLOSS 686 PLUS on paver tiles; first install tiles then clean well and let dry. Apply 686 PLUS with a brush, sprayer or roller, or sponge mop. Be sure to work first coat into tiles so sealer penetrates deep into tile. When visibly dry; apply light coat. If the surface darkens like it is getting wet, it is not sealed yet, and needs another coat. When you apply the coat where the surface does not darken like it is wet; then it is sealed. Let dry over night. Grout the pavers. Wait for grout to cure. Then after your surface is clean and completely dry; again apply ULTRA HIGH GLOSS 686 PLUS as above to the grout and stone. Work in well into grout. 686 PLUS will help strengthen grout as well as add to the beauty. Extra coats will add to the depth of shine. Allow 48 to 72 hours for the surface to cure. Walk on traffic in 4 hours. DO NOT APPLY SEALER UNLESS THE SURFACE IS COMPLETELY DRY AND NEUTRALIZED FROM ANY ACID USE. For use on brick and stone; above directions apply. DO NOT LET PUDDLE ! If left to puddle; sealer will not dry clear.

One gallon of ULTRA HIGH GLOSS 686 PLUS will cover approximately 200 to 250 square feet per gallon, depending on how porous the surface is. That is how much sealer we estimate on an average surface to get it totally sealed. That includes all coats. This is a multiple coat product. When using as a joint stabilizer; spread sand over the pavers, and squeegee the surface clean. Spray on sealer then again squeegee the surface to avoid puddling, and work into joints. Figure about one gallon per 100 sq. ft. on 12 X 12 pavers. When using on decomposed granite; figure about 30 to 40 sq. ft. per gallon.

Do not use below 55 degrees, or in hot mid-day direct sun. Do not let HIGH GLOSS 686 PLUS puddle or run down vertical surfaces. When testing for desired results; be sure to allow 48 to 72 hours for curing. Neither 686 Plus or 646 Plus are not for use on ceramic, porcelain, polished marble or polished granite.

Although 686 PLUS is a relatively tame product; use rubber gloves when applying. Avoid contact with skin. Prolonged exposure to vapors may be harmful or fatal. Use in well ventilated area. In conditions which do not permit good ventilation; use of a breathing apparatus is recommended.

Our only obligation shall be to refund purchase price or replace any of our product proved to be defective. Beyond purchase price of materials supplied by us, we assume no liability for damages of any kind and the user accepts the product "as is" and without warranties either expressed or implied. The suitability of the product for an intended use shall be solely up to the user.

STORE ABOVE 40 F - DO NOT FREEZE. Duro Shine Sealers LLC Po Box 5358 - North Hollywood, Ca. 91616. 686 PLUS is available in quarts, gallons and 5 gallon pails.